INSTALLATION AND OPERATION
INSTRUCTIONS
Í
MODEL: SL-350TRSI-AUE
AUSTRALIAN GAS ASSOCIATION APPROVED
Approval Number 5666
THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED
BY HOMEOWNER FOR OPERATION AND MAINTENANCE.
HEAT & GLO, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044 USA
THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:
(United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474,
6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada) 1297749,
2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265;or other U.S. and foreign patents pending.
Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06
1
TABLE OF CONTENTS
1.0 Installation Instructions......................................................................................... 5
1.1 Introduction ................................................................................................... 6
Í
1.2 Flue SystemApprovals and Installation ......................................................... 8
1.3 Connecting the Gas Supply ........................................................................ 22
1.4 Ignition System Wiring ................................................................................ 23
1.5 Blower Fan................................................................................................. 24
1.6 Finishing .................................................................................................... 25
1.7 Installer Testing ........................................................................................... 26
Í
1.8 Log Placement ........................................................................................... 27
2.0 Operating Instructions ....................................................................................... 30
2.1 Safety and Lighting Information................................................................... 31
2.2 Fan Operation ............................................................................................ 32
3.0 Servicing and Maintenance............................................................................... 32
3.1 Removal of Covers for Servicing ................................................................ 33
3.2 Removal of Components for Service .......................................................... 33
3.3 Parts Replacement..................................................................................... 33
3.4 Adjustments and Replacement Parts .......................................................... 33
3.5 Troubleshooting .......................................................................................... 34
Í
4.0 Replacement Parts ........................................................................................... 35
Limited Warranty............................................................................................... 37
Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06
3
22-3/4 in.
(577mm)
11-3/8 in.
(289mm)
16-3/8 in.
(414mm)
15-7/8 in.
(402 mm)
8-3/4 in.
(223mm)
Ø6-5/8 in.
(167mm)
Ø8 in.
(203mm)
ELECTRICAL
ACCESS
24 in.
(610mm)
GAS LINE
ACCESS
41-3/4 in.
(1060mm)
30 in.
(764mm)
15-1/8 in.
(384mm)
3-1/2 in.
(90mm)
21-3/8 in.
(542mm)
30-5/8 in.
(777mm)
2-1/8 in.
(55mm)
28-1/8 in.
(714mm)
5-5/8 in.
(144mm)
6-7/8 in.
(175mm)
33 in.
(837mm)
TOP STANDOFFS
FLUE COLLAR
COVER PLATE
HOOD
RATING PLATE/LABELS
( BEHIND DOOR)
BOTTOM
ACCESS DOOR
GAS
CONTROLS
( BEHIND DOOR)
ELECTRICAL
ACCESS
GAS
ACCESS
Í
Figure 1. Diagram of SL-350TRSI-AUE
Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06
4
Clearance Requirements
The top and back of fireplace are defined by stand-offs.
Top Flue
1in. Min. (25mm)
The heat shield must be attached as shown if combus-
tible materials are placed directly on top standoffs (Fig-
ure 3).
B
The minimum clearance to a perpendicular wall ex-
tending past the face of the fireplace is 25mm.
A
The back of the fireplaces may be recessed into com-
bustible construction, as shown above.
TOP
STANDOFFS
E
D
INSTALLED
HEAT SHIELD
C
½ in. Min (13mm)
A
B
C
D
E
Millimeter
837
413
728
1001
1416
Rear Flue
HEAT SHIELD
1 in. MIN. (25mm)
B
Figure 3. Heat Shield
A
1.0 INSTALLATION INSTRUCTIONS
NOTE: Not intended for fireplace insert.
In planning the installation for the heater it is necessary
to determine where the unit is to be installed, the type
of flue system to be used (straight out, corner, or el-
evated), and whether optional accessories (wall switch
or remote control) are desired. Gas supply piping should
also be planned. Refer to the appliance data plate on
the base pan of the heater for all gas pressures and
input rate information.
E
D
C
The heater can be mounted on any of the following sur-
face:
1 in. MIN. (25mm)
A
B
413
C
D
E
1. A flat surface (minimum 6mm base).
2. Four (4) corner supports.
Millimeter
837
843
1192
1686
(Example: Four (4) concrete masonry blocks). These
supports must be positioned so they contact all four (4)
perimeter edges on the bottom of the unit.
Figure 2. Fireplace Dimensions, Locations, and
Space Requirements
Heater framing can be built before or after the heater is
set in place. Framing should be positioned to accom-
modate wall covering and heater facing material. The
heater framing should be constructed of 2" X 4" (51 x
102mm) lumber or heavier. The framing headers may
rest on the heater standoffs. Refer to Figure 2 and Fig-
ure 4 for heater and framing reference dimensions.
Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06
5
|